1、SY5000/CMU-BATS Auto Switch controllerUser ManualV1.1CONTENTS1.FEATURES2.2.CONTROLLER EXTERIOR FIGURE3.3.PARAMETER RANGE AND DEFINE3.4.OPERATION4.4-1KEY FUNCTION4-2SETTING PARAMETER4-3MANUAL OPERATION4-4AUTOMATIC OPERATION5.FACTORY DEFAULTSPARAMETER5.6.INSTALLATION5.7.TYPICAL WIRING DIAGRAM6.8.SALE

2、SERVICE7.1、FEATURESSY5000/CMU-B double power switching controller is based on micro processor as the core of the new generation of intelligent controller. Real-time monitoring the mains and backup power these two road voltage. Be able to appear lost electricity,over-voltage,undervoltage,phase lack,e

3、tc,abnormal conditions make accurate judgement.And by manual or automatic mode switch ATS switch movement,which realizes automatic and unattended function,etc.n The ATS controller be used LCD digital design,Parameters is Chinese and English display.n The product can accurately acquisition and displa

4、y the main power/second power two way three-phase voltages.n The product parameter settings by password protection.n The ATS controller power supply mode can set mains power priority,backup power priority or no priority.n When a switch off failure,if another voltage to normal,the ATS controller will

5、 automatically switch to the way.n The ATS controller can install voltage alarm value and delay switch time.n The product have generator start function.n The ATS controller can chose single-phase/three-phase display,monitoring.n The product have two way N line separation design.n The ATS controller

6、can autosave fault record,inquires is more conveniently.n The ATS controller can be used DC power(935Vsupply or A/N phase voltage.2、CONTROLLER EXTERIOR FIGURE SY5000CMU-B3、SPECIFICATIONS3.1Power Supply :DC12V (range from 9to 35V ;AC220V (197-270V L-N3.2Generator input Voltage Range :0to220V AC ,3pha

7、se 4wire 3.3Power dissipation :<3VA at rated voltage34Operating Temperature Range :-20to +60Humidity Range :20to 754、OPERATION4-1、controller display properly state as follows: 4-2、SETTINGPARAMETERPress the key 5seconds,enter "password"interface,Input 4digit password,User can only by mon

8、itoring software to modify this password,Ordinary users password:1234Password input method:In the input password interface,Press the key,value add 1,Whenvalues increase to password bits,Pressthe key confirmation,Then interface jump to the second password bits,Repeat the above operation,input the rem

9、aining three password bits,and then enter into "menu",if a password mistake will not have access to menu system. In the menu system,Press thekey into the next page ,Press the key to modification parameter.When the control screen upward modification parameter.Then press key to increase the

10、value,Increased to maximum continuous buttons,then the system automatically return to low cycle.If press key,then exit set condition returns to the system default state.4.3Manual switching operationWhen the user manual debugging ATS switch,Through panel of buttons can be manually switched,each time

11、press the button will switch to correspond to the end.Specific steps: Press thekey will be the key controller is set to "manual"state,If switch to the main source control please press the key,If switch to standby power control please press the key.Note:in key-press,controller has 6seconds

12、countdown switch time,press other switch button is invalid,and if the countdown unfinished.0000 User can also through input password,the system parameters interface to "manual","automatic"Settings4.4Automatic switching set operationwhen the movement User Settings ATS switch autom

13、atically,need through controller internal priority to set up"the mains priority"-"standby power priority"-"no priority".Specific steps:First press thekey to enter the password Settings,enter the correctpassword and press thekey to scroll to"power priority model&quo

14、t;interface,After presskey choose"mains first"or"standby power first"or"no priority"of three modes.If exit system press thekey.5、FACTORY DEFAULTS PARAMETERTepy Factory Reset Set rangemains under voltage200V180V-220Vmains over voltage240V230V-250V200V180V-220VBackup powe

15、r undervoltage240V230V-250VBackup power overvoltageMains time delay normal5S0-60S5S0-60SMains time delayabnormalBackup time delay5S0-60Snormal5S0-60SBackup time delayabnormalGenerator start time0S0-90Sdelay5S0-90SGenerator stop timedelayPrior supply mode mains power priority:mains power priority:bac

16、kup power priority:not priorityStatus Auto:manual:autoSupply display mode Display three phase DisplayDisplay switch time Recover factory set 6S Not recover single-phase/three phase 1-9S :recover :not recover 6、 controller mounted controller mounted： With the product distribution two installation ear

17、s fixed. Overall dimension：140x120x56mm (W X H X D Cut-out for fix dimension: 128x112mm (W X H 7、connection diagram 7-1、 According to SY5000/CMU-B controller of each port after shell that correct connection wiring. SY5000/CMU-Bback diagram 6 7-2、 SY5000/CMU-B controller wiring terminal explain Termi

18、nal A1、B1、C1、N1 Wiring explain Remark Connect mains AC 198V-242V A,B,C,N M1、M2 Connect relay output 16A 250VAC CLOSE 1# L1、L2 Connect AC battle AC 198V-242V line VIN、GND connect DC Controller power plus-minus supply DC 9V-36V M3、M4 Connect relay output 16A 250VAC CLOSE 2# A2、B2、C2、N2 Connect backup power AC 198V-242V A,B,C,N M5、M6 Connect generator 10A 250VAC relay output According to SY5000/CMU-B controller of each port after shell that cor