1、工廠驗收報告Factory In specti on ReportWord資料HDPE硅芯管工廠驗收報告HDPE silicore duct Factory Inspection Report測試目的Test Purpose確保HDPE硅芯管出廠產品質量指標符合合同技術標準要求。測試依據Test Sta ndard合同約定技術要求。產品名稱ProductNameHDPE 硅芯管 HDPE silicore duct規格型號ProductModel40/33mm買方Buyer賣方Seller測試人員Tester工廠驗收結論Inspection Results該批HDPE硅芯管420000米經現場

2、隨機抽樣檢測， 各項技術指標均符合合同約定技術要求，準予出廠買方. *賣方： *代表簽字：代表簽字：日期：日期：驗收人員名單Factory Tester List姓名Name單位Compa ny職務Positi on簽字Sig nature高級經理SeniorMan ager副經理DeputyMan ager經理.頁腳40/33mm HDPE硅芯管一工廠測試記錄40/33mm HDPE silicore duct -Factory Inspection repor項目Items檢驗標準及方法Test sta ndard andmethod要求Requireme nt實測值Test value說

3、明Remark外觀Appearance在自然光線下目測。Checked by eyes un der n atural light顏色均勻一致、內外 壁平整、光滑，無明 顯雜質、氣泡，產品 上標識完整、清晰。Uniform color,in side andoutside walls aresmooth, noimpurities,bubbles, productidentification iscomplete andclear.用分度值0.02mmn尺測平均外徑量。 400.3mmMeasured byn ruler withAverage ODdivisio n value 0.02mm

4、. 400.3mm用分度值0.02mm卡尺測壁厚 3.6 ± 0.2mm尺寸量。Wall thick nessDime nsiMeasured by caliper with3.6 ± 0.2mmondivisio n value 0.02mm.用分度值1mm的卷尺測測量米標長量。長度 1500+o.3%-°m度，用讀數Measured by tapeLen gth值乘記碼數measure with divisio n1500+0.3%-0mMeasuri ngvalue 1mm.meterlen gth, readi ng records multiplyi n

5、g code No.包裝Package按用戶確認的包裝要求檢驗Check ing as per customerspackagerequireme nt標記Marki ng1、目測標記清晰度；Visualcheck ing marking defi niti on.2、米標誤差土 0.5刑etermark tolera nee± 0.5%.按用戶確認 的要求印字 內容檢杳Check ing as per customers 'marki ng requirement幾何尺寸GeometrVerification of the ratio of thepipe diameter

6、 to wallthick ness (SDR)檢杳硅芯管直SDR11y徑和壁厚的比值環剛度按照 GB/T24456-2009 檢測。Ri ngTested accordi ng to三 50KN/m2stiff nessGB/T24456-2009.外壁硬度按照 GB/T24456-2009 檢測。Hardn essofTested accordi ng to三 59HDexter nal wallGB/T24456-2009.Air用不透氣的堵頭封閉硅芯管pressure2端，加壓至0.2 MPa，保持test此壓力24小時，看壓力值（不(leaks)變)The whole cylinde

7、r of空氣壓力the duct is takenand測試sealed at both ends with不破不裂air-tight plugs and theNo crack.system is the n in flated upto a pressure of 0.2 MPa.After keepingit at suchpressure for 24 hours,read the pressure withoutproduci ng losses.用不透氣的堵頭封閉硅芯管兩端，加壓至1.27 MPa，保持1小時后泄壓，（做3個循環），看壓力值（不變）。短期壓力Blocked both

8、 ends of測試silic one duct with不破不裂Short-tergas-tight plug,No crack.m stresspressurized up to 1.27testsMPa for one hour (3cycles), the n check thepressure value.(withoutloss)硅芯管服務壽命用加速老化測試證實，80。持續165小時后測試性能，至少達到加速老化未試驗前60%性能。經老化后，各項性能測試Accelerated aging test三60%設計值Accelerto prove the service life ofAf

9、ter aging, allatedsilic on duct. The duct atperforma neeag ing80 ° C for 165 hours, then=60% designtesttest the performa nee, atvalue.least with 60%performa nee beforetest ing.扁平試驗Flatti ngtest兩端各200mm的樣品置于 平板的上下端之間，加壓速 率為10 mm/min ，垂直加壓 至外徑變形量為原來的50% 時，持續30分鐘后測量偏向 指標。Two samples with 200mm in

10、dividually placed betwee n the top and bottom of the plate, pressurized vertically un til the outer diameter deformed of origi nal 50%, and last ing for 30 minutes, then test deflect ion in dex.試驗后能夠在10分 鐘內回復到原外徑 的 70%。Within 10 minu tes after testi ng, it can revert to 70% origi nal OD.拉伸屈服強度Ten si

11、le stre ngth按 GB/T8804.2-1988 規 疋的方法，取五個沖裁試樣， 分別夾持在試驗機上，拉伸速 度為100mm/mi n,直至將試 樣拉斷,記下拉伸過程中的最 大拉伸值為試驗結果，取五次三 20MPa有效試驗的算術平均值為測 試結果。According to the methodprescribedinGB/T8804.2-1988,putt ing5 samples to nip in the testequipme ntin dividually,withtheten sile speed 100mm/min un til the sample break ing,

12、 note the Max.ten silevalueduri ngten sileprocess,andkeeprecord of averagevalueof five times.斷裂伸長率Elon gatio n at break根據 GB/T 8804.2-1988 取 5 個樣品，以100 mm/min 速率拉伸直至樣品斷裂，看斷裂時的延伸指標，取5個樣 品結果的平均值。Taking 5 samples accordi ngtoGB/T 8804.2-1988, with theten silespeed100mm/mi nun til the三 350%sample break

13、ing,checktheelon gati onvaluewhe n it breaks, and keep record of average value of five samples.斷裂張力Breaki n gtension取二段長度為200mm的元 整硅芯管試樣,試樣兩端應垂 直切平。用專用夾具將試樣 夾持在試驗機上，拉伸速度 為450mm/min ，直至試樣 屈服時，讀取試驗的屈服負 荷為試驗結果。若試樣在夾 具邊緣斷裂，則試驗無效， 應重新更換試樣。取三個有 效試驗的算術平均值為測試 結果。Taking three 200mm silic one duct samples, bo

14、th ends shall be cut flat vertically.The samplefixedinthetestequipme ntwith specialclamping, with the tensile speed 450mm/minun til三 8000N低溫沖擊測試Lowtemperatureimpacttestthe sample yield, readi ngthe testing yield load as the result. If the samples breaks on the edge of the clamp, the test is failure,

15、 shall replace the samples. Taking average value of three times valid value as the result.按GB/T24456-2009 規定的方 法，取10段長度為150mm的完 整硅芯管試樣，試樣兩端應垂直切平、無破裂、無裂縫等缺陷，將試樣放在溫度-20 C的試驗箱 中恒溫保持2h ,每次取出一個試 樣，落錘高度為 2m，錘頭直徑 50mm、質量15.3kg的條件下進 行沖擊，每個試樣沖擊一次，試樣 不破裂或裂紋寬度不大于 0.8mm為合格，10個試樣9個 以上合格為落錘沖擊試驗合格。按照 GB/T24456-200

16、9 檢測。Take 10 full length of150mm silicon core duct as sample, the ends of samples should be cut vertically and flat without any rupture, cracks and other defects. Put one sample on the platform of test machine for each impact test. The shape and size of the hammer head as follows:Put samples into th

17、e test ingcaseandmai ntai nthecon sta nttemperature of -20°C for 2hours. Taking one sample each time and impacti ng onceun derthecon diti ons of the drop hammer height of 2m, hammerdiameterof50mm and weight of15.3kg. The sample isqualified whe n there is nobreak and crack or thecrack is not gre

18、ater than0.8mm. In accorda neewithGB/T24456-2009,moretha n9 of 10samples passed the testare qualified for the drophammer impact testi ng.根據 GB/T 6671 -2001 測試，烤爐的溫度達到110 oC ±2熱收縮率oC。Heat ingTested as per GB/T 6671三3%Shri nk-2001,theoventemperature up to 110 oC± 2 oC.內摩擦系根據JT/T 496-2004方法測動態三0.15 （圓鼓數試。法）In ternal frictio nTestedas perJT/TDynam ic = 0.15coeffici ent496-2004.(drum method )管材管件取兩段長度為200mm的元三 5000N的連接力The connec ting stre ngth of fitt in gs整硅芯管，用硅芯管專用連 接頭按生產企業提供的工具 和方法連接好組成試樣，用 專用卡具將該試樣夾持到