1、Electric FansUL 867/C22.2 No.187 產品結構及測試要求（For Electrostatic Air Cleaner）Prepared By: Histo LingIntertek GuangzhouAug 16, 2010目錄Content of UL 867 and CSA C22.2 No. 187Introduction: Scope and general.Section 1 Mechanical Construction， 機械結構；Section 2 Electrical Construction， 電氣結構；Section 3 Components，

2、 零部件；Section 4 Safety Test， 測試；Section 5 Marking and Instructions，銘牌、說明書。Important words: CADR and CARBScopeUL867電壓不能大于600 V；靜電式；非危險地方使用；目的是除塵和加熱和通風設備中的顆粒。CSA C22.2 No. 187電壓不能大于600 V；靜電式；非危險地方使用；目的是除塵和加熱和通風設備中的顆粒。室內家用或者商用，不包括工業用；不包括專門設計來產生臭氧的空氣清新機Section 1 Mechanical Construction外殼：UL8671. 用于（移動式）外

3、殼的金屬材料厚度應滿足：不上漆是0.66 mm；鍍鋅是0.76 mm；其他是0.91 mm。尺寸小和通過卷曲等加強強度的除外。2. 木外殼的厚度不能小于 12.7 mm。3. 非金屬外殼（大部分為塑膠）滿足UL746C，最低HB可以滿足要求。CSA C22.2 No.1871. 用于外殼的金屬材料厚度應滿足：table 1, 2, 3。特別出管部分鋼鐵為0.78 mm； 非鐵材料部分為1.08 mm 。2. 非金屬外殼（大部分為塑膠）防火等級滿足CSA C22.2 No.0.17，要求5VA才能滿足要求。外殼測試UL867：外殼根據標準要求需要進行鋼球沖擊測試（6.8J包括護欄）來評估材料的抗

4、沖擊性能。要是外殼和護欄是非金屬，那么要分別在兩臺樣機上做沖擊測試，一臺直接沖擊，另一臺要在至少70度的條件下放置7小時然后冷卻到室溫再做沖擊。室外使用的設備要先在-35度條件下放置3小時再接著做沖擊。（clause 27）Section 1 Mechanical ConstructionCSA C22.2 No. 187非金屬外殼要做的外殼和護欄強度測試（推力50 N，只是針對帶電部件）。（clause 6.11）Accessibility of live part and Moving Parts (CSA只是針對開孔，不包括運動部件護欄）在檢查器具是否符合標準要求時，需要使用如下測試探棒

5、。并且該測試探棒應該施加最小的力，測試探棒不應該觸及危險的帶電部件和運動部件。Section 1 Mechanical ConstructionCSA只是針對開孔，不包括運動部件的護欄。運動部件的護欄家用設備要施加14 N的軸向力，非家用設備要施加28 N的軸向力。（6.12）Section 1 Mechanical ConstructionStrain Relief（抗拉裝置）為電源線提供適當?shù)目雇评靶D(zhuǎn)保護，有以下等類型：注：金屬壓線裝置不能單獨和SPT-1, SPT-2, SVT, SVTO 線型使用，需增加額外的保護，如套管。 * CSA 要求一個0.25 N*M的扭力。Spacin

6、g1. The spacings in a component device, such as a snap switch, a lampholder, a motor, and the like supplied as part of an air cleaner shall not be less than the minimum spacings required for the component device or the spacings specified in Table 23.1, whichever are smaller.Section 2 Electrical Cons

7、tructionSection 2 Electrical ConstructionThe spacings in a line-voltage circuit shall comply with Table 23.1. Exception No. 1: Minimum 1/32 inch (0.8 mm) through air and over surface spacings before potting for parts that are potted in an insulating compound may be applied. A thermoplastic potting c

8、ompound is to be evaluated with regard to its acceptability for the application. If an investigation is necessary to determine if a material may be used, such investigation is to be conducted in accordance with the Standard for Polymeric Materials Use in Electrical Equipment Evaluations, UL 746C. Co

9、nsideration is to be given to:a) The mechanical strength of the material, resistance to hot wire ignition, resistance to highcurrent- arc ignition, resistance to high-voltage-arc ignition, dielectric strength, insulation resistance, and heat-resistant qualities, in both the aged and unaged condition

10、s;b) The degree to which the material is enclosed; andc) Any other feature affecting the risk of fire, electric shock, electrical high-energy current levels, or injury to persons. All factors are to be considered with regard to conditions of actual service. Exception No. 2: On a printed-wiring board

11、, the over surface spacing may be reduced to 1/32 inch (0.8 mm) if the board is coated with a conformal coating complying with the Standard for Polymeric Materials-Use in Electrical Equipment Evaluations, UL 746C. Exception No. 3: On a printed wiring board, spacing requirements (other than for spaci

12、ngs to ground, between different circuits, and at field wiring terminals) may be waived between traces of different potentials connected in the same circuit if:a) The spacings comply with the Evaluation of Reduced Spacings on Printed-Wiring Boards, Section 48;b) The printed-wiring board has a flamma

13、bility classification of V-0, in accordance with the requirements in the Standard for Tests for Flammability of Plastic Materials for Parts in Devices and Appliances, UL 94; andc) The printed wiring board is constructed from a base material having a minimum Comparative Tracking Index (CTI) Performan

14、ce Level Category rating of 2 in accordance with the Standard for Polymeric Materials Use in Electrical Equipment Evaluations, UL 746C.Section 2 Electrical Construction23.4.1 Spacings between an insulated or uninsulated high-voltage part and: a) Insulated or uninsulated line-voltage circuit parts, b

15、) Other high-voltage parts of opposite polarity, and c) Dead metalSwitches or other control devices1、開關的額定值不能小于其所控制的負載的額定值；2、標有OFF的開關應和火線連接；3、控制非電機感性負載（如變壓器、鎮流器）的開關，其額定電流應為所控制負載的額定電流的兩倍以上；4、PCB的防火等級要求為V-2以上。Capacitor1、電機啟動電容，需經UL 810認證；2、X和Y電容需經UL1414認證或通過UL1283耐壓、絕緣電阻及耐久測試。Section 3 ComponentsMotor

16、1、馬達應該具有UL或ETL認證，并符合UL 1004-1/2/3/4, CSA C22.2 No. 100和CSA C22.2 No.77的要求；2、A級絕緣系統馬達內的電氣部件、塑料部件以及絕緣材料須有相應的UL認證；3、B級以上絕緣系統馬達，除電氣部件、塑料部件要有認證外，還需提供相關的絕緣系統認 證。以下部件須經認證： 塑膠、內部線、開關、奶嘴、熱縮套管、玻纖套管、PCB、變壓器、溫控器、保險絲、繼電器、壓敏電阻等。特別是馬達部品：漆包線，絕緣材料（絕緣紙，絕緣槽等）Section 3 ComponentsUL 867 & CSA C22.2 No. 187:Impact Test S

17、tability External Surface Temperature Leakage Current Test Leakage Current Following Humidity Conditioning Input Test Output Test Ozone Test Peak Ozone Emission Location Determination Test Strain Relief Test Pushback Relief Test Grounding Resistance Test Temperature Test Section 4 Safety TestUL 867

18、& CSA C22.2 No. 187:Dielectric Voltage-Withstand Test Stored Energy Test Abnormal Operation Test High-Voltage Insulating Material Arcing Test UL746C:Resistance to Impact TestAbnormal Operation TestSevere Conditions TestMold Stress-Relief Distortion TestInput to Motors TestSection 5 Marking and Instructio