1、Quality Control ChecklistWood Furniture1. Rough Mill:1.1 Check moisture content on lumber in kiln. Check moisture on plywood parts.1.2 Check to insure rough cut parts are the correct length, width, height or thickness to allow for machining.1.3 Check to insure there are no dead knots in the parts an

2、d that the live knots conform to product quality requirements.1.4 Inspect for wind shake, splits, honeycombs, cracking, etc.2. Lamination Department:2.1 Insure that parts to be laminated are laminated on both sides before clamping.2.2 Insure that grain direction is reversed on all parts being lamina

3、ted.2.3 Inspect for moisture content after the lamination process.2.4 Inspect for rough cut sizes to insure allowances are made for machining, length, width, height or thickness.3. Machine Department:3.1 All parts need to be checked for proper size and machiningaccording to the detail.3.2 Inspect mo

4、isture content. (If moisture content is above 8% re-dry parts.)3.3 All parts machined to spec sheets and FC standard spec Bk.3.4 There are no parts splitting or cracking.3.5 There are no open grains.3.6 Check for parts being square when applicable.3.7 Dry fit parts to check for proper fit.3.8 Check

5、all right angles.3.9 Inspect tops with straight edge for warping.3.10 Check Rab Parts for proper depth and consistent machining.3.11 Check that all reveals are clean at 90% and uniform in size and length.3.12 Inspect door style, door, side panels, parting rails, etc. For proper construction and warp

6、ing (Use straight edge).3.13 Check all board and mortised parts for proper size boring and tennon.3.14 Check all miters and compound miters for consistency and fit.3.15 Check boring for hardware, shelves and adjustable shelf hole spacing.3.16 All reveal and tops are uniform in size.3.17 Insure that

7、bunn feet that cannot be turned into the carcuss post have the correct dowel length.4. Carving Department:4.1 Check that all carvings are consistent and complete. ( Used mirror image concept)5. Pre Assembly:5.1 Check to insure that parts fit properly.6. Pre Sanding - Parts Sanding:6.1 Insure all par

8、ts are sanded properly.6.2 Insure that the edges are broke on all parts.6.3 Pre-fill all tops that have open grain.7. Assembly:7.1 Check carcuss to insue proper fit at all joints and that they are properly glued and screwed.7.2 Insure the carcus is leveled. (Sits Level)7.3 Check outter carcus for sq

9、uare.7.4 Check all door and drawer compartments for square and proper dimension.Check carcus top for level, front, back, and sides (Use straight edge)7.5 Insure that all items are strong and stable. (Use-weight test by applying minimal pressure)7.6 Check | cor ner blocks to in sure they have bee n g

10、lued and screwed.7.7 Check parting rails to include dust bottom for proper fit and that they are not| warpi.7.8 Check all under arts for uniformity. (Table Apron)7.9 Check to in sure proper bridgi ng is in stalled on all tables.7.10 Check for proper Drawer Costructi on and pitch.7.11 Check for prope

11、r shelf fitt ing and clear nee for no stick ing and proper cleara nee. ( By F.C Specs Book)7.12 Check to in sure that all in side and out side dime nsions are correct accord ing to the overall size.7.13 Check chair seat depths.7.14 In sure that all pitchs conform to specificati ons.7.15 In sure no g

12、auges, scratches, den ts, n ails or spli ntered areas are on the item.7.16 All drawer and door deges need to be rounded. (Hand Sand Edges)7.17 In sure that all Rerlays have bee n properly allig ned, glued and pinned n ailed.7.18 All doors and side pan els being a solid or vfcn eered panl must have a

13、 floating panel construction. (Check Spec. Book for Con struscti on)7.19 Check all legs for champer and rounding.7.20 In sure all bunn feet have bee n glued and screwed.7.21 Insure back panels are square and screwed on not glued.7.22 Check tops for proper instillation, fit and screwing.7.23 Insure b

14、rass is permanently fixed with epoxy and nailed, and taped for finishing purposes.Unit Sanding: 光澤Insure that proper sanding is done throughout the entire case.Insure all carvings are flutter sanded and hand sanded.Insure all gauges, dents, scratches, cracks it are filled and sanded.Cracks and split

15、s 1/8” or larger need to be slivered.No veneer used for patching on solid pieces.Patch follows grain in existing item as much as possible and patch does not have definite shape. EX. Square, round, oval, ect.All patches should be 1/4” in thickness for solid pieces.Check for glue runs.Polish SandingCh

16、eck surfaces inside and out for consistent sanding.Check carvings for proper final sanding.Finishing:Insure proper materials are being used according to the step panel. Insure the inside finish is consistent and matches the outside.Overall finish is even and consistent.Tops, bottoms and back panels

17、of items are to be finished.All surfaces are smooth and free of overspray.Check for the finnish cracking and peeling.Check for runs and fingefrprints in the finish.Insure drawer interiors are finished correctly.Check to insure all hand paintings are correct and consistent.Check final color against s

18、ample for variation.Packing:Before packing check to insure all hardware and hinges are installed correctly.Check joints for cracking.Allitems need to be blown off with air hose and inspected.Check to insure all interiors are clean.Check glass insert for proper fit.Check mirror insert fo proper fit.C

19、heck moisture content.Insure all items are wrapped in 4mm plastic proir to shipment.Stone Casting:Check for any imperfection in the stone.Inspect molds on a regular basis.All cast should be free of flat seams.Check for hair line cracks.Check for adjustable glides on all dining tables. When applicabl

20、e.Check for level surfaces for all items that require lay on glass.When applicable check items for square and level.When stone and metal are casted together issure there are no gaps or holes when they are joined.Insure items without adjustable glides sit level.Check dimensions according to the detail.Metal:Insure all items are level.Insure items that require lay on glass the surface is level.Insure dimensions are correct according to the detail.When possible adjustable glides need to be added to dining tables. Check for grinding or