1、armcfg:1Bind a LUN1Unbind a LUN2Change LUN Ownership2Replace a LUN3armmgr:3Add a Hot Spare3Remove a Hot Spare3Set the Cache Page Size3Assign an alias to a disk array4Set on one controller; automatically syncs the second controller4Change controller state from passive to active4Synchronize the contro

2、ller date and time with the host4Reset battery age to zero when the battery is replaced4Perform a parity scan on a LUN4amutil:4Disable Disk Write Cache (WCE)4Locate a disk module by flashing its amber LED4Flush (retrieve) disk array controllers event logs4Change a disks state by manually failing the

3、 disk4Hardware States control4amdload:5amdsp:5Disk Array Status Commands5Rescan for all disk arrays on the host5List all disk arrays recognized by the host5Check the status of the rebuild process5Identify disks5amlog:5armcfg:Bind a LUNamcfg -L <cntrlrID>:<LUN> -d <channel:ID>,<c

4、hannel:ID> -r <RAIDlevel> <options> <ArrayID>where:cntrlrID Identifies the controller (A or B) that will own the LUNLUN Number assigned to the LUNchannel:ID Identifies the channel and SCSI ID of each disk,in the LUN Multiple disks must be entered without spaces between disk iden

5、tifiersRAIDlevel RAID level to be used for the LUN, Valid values are 1 and 5 A RAID 0/1 LUN is created by selecting RAID 1 with a even number of more than two disksoptions -c capacityCapacity of the LUN in M (megabytes) orG (gigabytes)Default is entire capacity of disk modulesIf M or G are not speci

6、fied, default is G-forceOverrides the HA protection that preventsusing two or more disks in the same SC10or on the same channeloptions -s stripeStripe segment size in KbytesMust be a multiple of the current cachepage size settingDefault is the same block size used forcache pages, either 4 or 16 Kbyt

7、esArrayID The FC60 serial number or aliasExample of command for binding a 5-disk RAID 5 LUN onan FC60 whose serial number is 0000005EBD20:amcfg -L A:2 -d 1:1,2:2,3:0,4:4,5:3 -r 5 -s 16 0000005EBD20Example of command for binding a 4-disk RAID 0/1 LUN on an FC60 whose alias is HPSU_1:amcfg -L B:6 -d 1

8、:8,2:8,3:8,4:8 -r 1 -s 16 HPSU_1Unbind a LUNamcfg -D <LUN> <ArrayID>where:LUN Number assigned to the LUN to be unboundArrayID The FC60 serial number or aliasExample of command for unbinding RAID 5 LUN on an FC60 aliased “rack_1”:amcfg -D 5 rack_1Change LUN Ownershipamcfg -M <LUN> -

9、c <cntrlrID> <ArrayID>where:LUNNumber of the LUN whose ownership is beingchanged to the other controllercntrlrIDThe controller (A or B) that will become the ownerof the LUN ArrayIDThe FC60 serial number or aliasExample of command for changing ownership of LUN 5 from controller A to contr

10、oller B on FC60 0000005EBD20:amcfg -M 5 -c B rack_1Replace a LUNReplace a LUN by unbinding and rebinding it with a single command; intended for LUN 0amcfg -R <cntrlrID>:<LUN> -d <channel:ID>, <channel:ID> -r <RAIDlevel> <options> <ArrayID>The replace command

11、 unbinds a LUN and rebinds it with the parameters specified in a single operation This command is intended to be used only to replace the LUN 0 that is automatically created when the FC60 is powered up the first time For all other LUNs, it is recommended that the bind and unbind commands be used to

12、alter the LUN The command is identical to the bind command except that the -R option is used instead of the -L option amcfg -R <cntrlrID>:<LUN> -d <channel:ID>,<channel:ID> -r <RAIDlevel> <options> <ArrayID> armmgr:Add a Hot Spare ammgr -h <channel:ID>

13、 <ArrayID>channel:ID Identifies the channel and SCSI ID of the disk to be used as the hot spareArrayID The FC60 serial number or aliasExample of command for adding a hot spare using disk module 1:1 on FC60 0000005EBD20:ammgr -h 1:1 0000005EBD20Remove a Hot Spare ammgr -d <channel:ID> <

14、;ArrayID>channel:ID Identifies the channel and SCSI ID of the hot spare disk to be returned to the unassigned disk groupArrayID The FC60 serial number or aliasExample of command that removes disk 2:3 as a hot spare on FC60 aliased “rack_5”:ammgr -d 2:3 rack_5Set the Cache Page Size ammgr -p 4:16

15、<ArrayID>4:16The cache page size can be set to either 4 Kbytes or 16 KbytesArrayIDThe FC60 serial number or aliasExample that sets the cache page size to 16 Kbytes:ammgr -p 16 rack_10Assign an alias to a disk arrayammgr -D <ArrayAlias> <ArrayID>Aliases can include upper and lower c

16、ase characters, numbers, pound sign (#), period (.) and underscore (_)Set on one controller; automatically syncs the second controllerammgr -L <cntrlrID>:<percent> <ArrayID>Change controller state from passive to activeammgr -c AA <ArrayID>The state cannot be set from active

17、to passiveSynchronize the controller date and time with the hostammgr -t <ArrayID>Reset battery age to zero when the battery is replacedammgr bPerform a parity scan on a LUNammgr -P <LUN> <ArrayID>ammgr -P <LUN> -fp <ArrayID>The fp option indicates that any parity error

18、s should be corrected to match the associated dataamutil:Disable Disk Write Cache (WCE)amutil w ArrayIdamutil w on ArrayIdLocate a disk module by flashing its amber LEDamutil -f ch:id <ArrayID>Flush (retrieve) disk array controllers event logsamutil -l <ArrayID>Change a disks state by ma

19、nually failing the diskamutil -D channel:ID | -d channel:ID <ArrayID>格式化fc60的硬盤amutil -syswipe (arrayid)Hardware States controlamutil C A arrayid Fail a controlleramutil c A arrayid unfailamutil c AA arrayid passive to activeamutil -Q A arrayid quiesce a Controlleramutil D channel:ID fail a di

20、skamutil rr channel:ID mark a disk replacedamutil P arrayid parity Scanamdload:Downloading Firmware amdload -C all:A:B /path/FW_03010303_03010302.dlp <Array ID>amdload -C all:A:B /path/42032dx.dlp <Array ID>amdload -D all:A:B /path/ <ArrayID>看fc60的控制卡的firmware的版本號amdload -i arrayidalso Can display firmware re