1、交換機命令Quidwaydis cur ；顯示當前配置Quidwaydisplay current-configuration ；顯示當前配置Quidwaydisplay interfaces ；顯示接口信息Quidwaydisplay vlan all ；顯示路由信息Quidwaydisplay version ；顯示版本信息Quidwaysuper password ；修改特權用戶密碼Quidwaysysname ；交換機命名Quidwayinterface ethernet 0/1 ；進入接口視圖Quidwayinterface vlan x ；進入接口視圖Quidway-Vlan-in

2、terfacexip address ；配置VLAN的IP地址Quidwayip route-static ；靜態路由網關Quidwayrip ；三層交換支持Quidwaylocal-user ftpQuidwayuser-interface vty 0 4 ；進入虛擬終端S3026-ui-vty0-4authentication-mode password ；設置口令模式S3026-ui-vty0-4set authentication-mode password simple 222 ；設置口令

3、S3026-ui-vty0-4user privilege level 3 ；用戶級別Quidwayinterface ethernet 0/1 ；進入端口模式Quidwayint e0/1 ；進入端口模式Quidway-Ethernet0/1duplex half|full|auto ；配置端口工作狀態Quidway-Ethernet0/1speed 10|100|auto ；配置端口工作速率Quidway-Ethernet0/1flow-control ；配置端口流控Quidway-Ethernet0/1mdi across|auto|normal ；配置端口平接扭接Quidway-Eth

4、ernet0/1port link-type trunk|access|hybrid ；設置端口工作模式Quidway-Ethernet0/1port access vlan 3 ；當前端口加入到VLANQuidway-Ethernet0/2port trunk permit vlan ID|All ；設trunk允許的VLANQuidway-Ethernet0/3port trunk pvid vlan 3 ；設置trunk端口的PVIDQuidway-Ethernet0/1undo shutdown ；激活端口Quidway-Ethernet0/1shutdown ；關閉端口Quidway

5、-Ethernet0/1quit ；返回Quidwayvlan 3 ；創建VLANQuidway-vlan3port ethernet 0/1 ；在VLAN中增加端口Quidway-vlan3port e0/1 ；簡寫方式Quidway-vlan3port ethernet 0/1 to ethernet 0/4 ；在VLAN中增加端口Quidway-vlan3port e0/1 to e0/4 ；簡寫方式Quidwaymonitor-port <interface_type interface_num> ；指定鏡像端口Quidwayport mirror <interfac

6、e_type interface_num> ；指定被鏡像端口Quidwayport mirror int_list observing-port int_type int_num ；指定鏡像和被鏡像Quidwaydescription string ；指定VLAN描述字符為了將交換機配置成一個集群的命令交換機,首先要給管理接口分配一個IP地址,然后使用下列命令: switch(config)# cluster enable cluster-name 21. 為了從一條中繼鏈路上刪除VLAN,可使用下列命令: switch(enable) clear trunk module/port v

7、lan-range 22. 用show vtp domain 顯示管理域的VTP參數. 23. 用show vtp statistics顯示管理域的VTP參數. 24. 在Catalyst交換機上定義TrBRF的命令如下: switch(enable) set vlan vlan-name name name type trbrf bridge bridge-numstp ieee|ibm 25. 在Catalyst交換機上定義TrCRF的命令如下: switch (enable) set vlan vlan-num name name type trcrf ring hex-ring-num

8、|decring decimal-ring-num parent vlan-num 26. 在創建好TrBRF VLAN之后,就可以給它分配交換機端口.對于以太網交換,可以采用如下命令給VLAN分配端口: switch(enable) set vlan vlan-num mod-num/port-num 27. 命令show spantree顯示一個交換機端口的STP狀態. 28. 配置一個ELAN的LES和BUS,可以使用下列命令: ATM (config)# interface atm number.subint multioint ATM(config-subif)# lane serb

9、er-bus ethernet elan-name 29. 配置LECS: ATM(config)# lane database database-name ATM(lane-config-databade)# name elan1-name server-atm-address les1-nsap-address ATM(lane-config-databade)# name elan2-name server-atm-address les2-nsap-address ATM(lane-config-databade)# name Quidwaydescription ；刪除VLAN描述字

10、符Quidwaydisplay vlan vlan_id ；查看VLAN設置Quidwaystp enable|disable ；設置生成樹,默認關閉Quidwaystp priority 4096 ；設置交換機的優先級Quidwaystp root primary|secondary ；設置為根或根的備份Quidway-Ethernet0/1stp cost 200 ；設置交換機端口的花費Quidwaylink-aggregation e0/1 to e0/4 ingress|both ;端口的聚合Quidwayundo link-aggregation e0/1|all ; 始端口為通道號

11、SwitchA-vlanxisolate-user-vlan enable ；設置主vlanSwitchAisolate-user-vlan <x> secondary <list> ；設置主vlan包括的子vlanQuidway-Ethernet0/2port hybrid pvid vlan <id> ；設置vlan的pvidQuidway-Ethernet0/2port hybrid pvid ；刪除vlan的pvidQuidway-Ethernet0/2port hybrid vlan vlan_id_list untagged ；設置無標識的vla

12、n如果包的vlan id與PVId一致，則去掉vlan信息. 默認PVID=1。所以設置PVID為所屬vlan id, 設置可以互通的vlan為untagged.路由器命令Quidwaydisplay version ；顯示版本信息Quidwaydisplay current-configuration ；顯示當前配置Quidwaydisplay interfaces ；顯示接口信息Quidwaydisplay ip route ；顯示路由信息Quidwaysysname aabbcc ；更改主機名Quidwaysuper passwrod 123456 ；設置口令Quidwayinterfa

13、ce serial0 ；進入接口Quidway-serial0ip address <ip> <mask|mask_len> ；配置端口IP地址Quidway-serial0undo shutdown ；激活端口Quidwaylink-protocol hdlc ；綁定hdlc協議Quidwayuser-interface vty 0 4Quidway-ui-vty0-4authentication-mode passwordQuidway-ui-vty0-4set authentication-mode password simple 222Quidway-ui-vt

14、y0-4user privilege level 3Quidway-ui-vty0-4quitQuidwaydebugging hdlc all serial0 ；顯示所有信息Quidwaydebugging hdlc event serial0 ；調試事件信息Quidwaydebugging hdlc packet serial0 ；顯示包的信息靜態路由：Quidwayip route-static <ip><mask>interface number|nexthopvaluereject|blackhole例如：Quidwayip route-static 129.

15、1.0.0 16 Quidwayip route-static Quidwayip route-static 16 Serial 2Quidwayip route-static 動態路由：Quidwayrip ；設置動態路由Quidwayrip work ；設置工作允許Quidwayrip input ；設置入口允許Quidwayrip output ；設置出口允許Quidway-ripnetwork ；設置交換路由網絡Quidway-

16、ripnetwork all ；設置與所有網絡交換Quidway-rippeer ip-address ；Quidway-ripsummary ；路由聚合Quidwayrip version 1 ；設置工作在版本1Quidwayrip version 2 multicast ；設版本2，多播方式Quidway-Ethernet0rip split-horizon ；水平分隔Quidwayrouter id A.B.C.D ；配置路由器的IDQuidwayospf enable ；啟動OSPF協議Quidway-ospfimport-route direct ；引入直聯路由Quidway-Ser

17、ial0ospf enable area <area_id> ；配置OSPF區域標準訪問列表命令格式如下：acl <acl-number> match-order config|auto ；默認前者順序匹配。rule normal|specialpermit|deny source source-addr source-wildcard|any例：Quidwayacl 10Quidway-acl-10rule normal permit source 55Quidway-acl-10rule normal deny source any擴

18、展訪問控制列表配置命令配置TCP/UDP協議的擴展訪問列表：rule normal|specialpermit|denytcp|udpsource <ip wild>|anydestination <ip wild>|anyoperate配置ICMP協議的擴展訪問列表：rule normal|specialpermit|denyicmp source <ip wild>|anydestination <ip wild>|anyicmp-code logging擴展訪問控制列表操作符的含義equal portnumber ；等于greater-th

19、an portnumber ；大于less-than portnumber ；小于not-equal portnumber ；不等range portnumber1 portnumber2 ；區間擴展訪問控制列表舉例Quidwayacl 101Quidway-acl-101rule deny souce any destination anyQuidway-acl-101rule permit icmp source any destination any icmp-type echoQuidway-acl-101rule permit icmp source any destination

20、any icmp-type echo-replyQuidwayacl 102Quidway-acl-102rule permit ip source destination Quidway-acl-102rule deny ip source any destination anyQuidwayacl 103Quidway-acl-103rule permit tcp source any destination destination-port equal ftpQuidway-acl-10

21、3rule permit tcp source any destination destination-port equal wwwQuidwayfirewall enableQuidwayfirewall default permit|denyQuidwayint e0Quidway-Ethernet0firewall packet-filter 101 inbound|outbound地址轉換配置舉例Quidwayfirewall enableQuidwayfirewall default permitQuidwayacl 101 ;內部指定主機可以進入e

22、0Quidway-acl-101rule deny ip source any destination anyQuidway-acl-101rule permit ip source 0 destination anyQuidway-acl-101rule permit ip source 0 destination anyQuidway-acl-101rule permit ip source 0 destination anyQuidway-acl-101rule permit ip source 0

23、destination anyQuidway-acl-101quitQuidwayint e0Quidway-Ethernet0firewall packet-filter 101 inboundQuidwayacl 102 ;外部特定主機和大于1024端口的數據包允許進入S0Quidway-acl-102rule deny ip source any destination anyQuidway-acl-102rule permit tcp source 0 destination 0Quidway-acl-102rule permit tcp

24、 source any destination 0 destination-port great-than1024Quidway-acl-102quitQuidwayint s0Quidway-Serial0firewall packet-filter 102 inbound ；設是路由器出口IP。Quidway-Serial0nat outbound 101 interface ;是Easy ip，將acl 101允許的IP從本接口出時變換源地址。內部服務器地址轉換配置命令(靜態nat)：nat server global <ip>

25、; port inside <ip> port protocol ;global_port不寫時使用inside_portQuidway-Serial0nat server global inside ftp tcpQuidway-Serial0nat server global inside telnet tcpQuidway-Serial0nat server global inside www tcp設有公網IP：202.38.160

26、.10103 可以使用。 ;對外訪問(原例題)Quidwaynat address-group 01 03 pool1 ;建立地址池Quidwayacl 1Quidway-acl-1rule permit source 55 ;指定允許的內部網絡Quidway-acl-1rule deny source anyQuidway-acl-1int serial 0Quidway-Serial0nat outbound 1 address-group pool1 ;在s0口從地址池取出IP對

27、外訪問Quidway-Serial0nat server global 01 inside ftp tcpQuidway-Serial0nat server global 02 inside www tcpQuidway-Serial0nat server global 02 8080 inside www tcpQuidway-Serial0nat server global 03 inside smt

28、p udpPPP設置：Quidway-s0link-protocol ppp ;默認的協議PPP驗證：主驗方：pap|chapQuidwaylocal-user q2 password simple|cipher hello ;路由器1Quidwayinterface serial 0Quidway-serial0ppp authentication-mode pap|chapQuidway-serial0ppp chap user q1 ;pap時，沒有此句pap被驗方：Quidwayinterface serial 0 ;路由器2Quidway-serial0ppp pap local-user q2 password simple|cipher hellochap被驗方：Quidwayinterface serial 0 ;路由器2Quidway-serial0ppp chap user q2 ;自己路由器名