1、精選文檔洛陽理工學院試驗報告系別計算機系班級B120503學號B12050316姓名段浴課程名稱計算機網絡試驗日期2014/11/8試驗名稱子網劃分路由配置成果試驗?zāi)康模?、 了解如何配置路由器信息2、 了解如何劃分子網試驗條件：電腦一臺，Cisco packet tracer模擬軟件試驗原理：在本試驗中，為您指定了一個網絡地址 192.168.9.0/24，您將對它劃分子網，并為拓?fù)鋱D中顯示的網絡安排 IP 地址。路由器全部使用2621XM，交換機全部使用2960。該網絡的編址需求如下： BRANCH1 的 LAN 1 子網需要 10 個主機 IP 地址。 BRANCH1 的 LAN 2 子

2、網需要 10 個主機 IP 地址。 BRANCH2 的 LAN 1 子網需要 10 個主機 IP 地址。 BRANCH2 的 LAN 2 子網需要 10 個主機 IP 地址。 HQ 的 LAN 子網需要 20 個主機 IP 地址。 從 HQ 到 BRANCH1 的鏈路的兩端各需要一個 IP 地址。 從 HQ 到 BRANCH2 的鏈路的兩端各需要一個 IP 地址。（留意：請記住，網絡設備的接口也是主機 IP 地址，已包括在上面的編址需求中。）Fa0/0Fa0/1LAN1LAN2LAN2LAN1試驗內容：1. 設計子網子網編號說明子網地址子網掩碼第一個可用地址最終一個可用地址1HQ 的 LAN1

3、92.168.9.0255.255.255.224192.168.9.1192.168.9.302BRANCH1 的 LAN 1192.168.9.32255.255.255.240192.168.9.33192.168.9.463BRANCH1 的 LAN 2192.168.9.48255.255.255.240192.168.9.49192.168.9.624BRANCH2 的 LAN 1192.168.9.64255.255.255.240192.168.9.65192.168.9.785BRANCH2 的 LAN 2192.168.9.80255.255.255.240192.168.

4、9.81192.168.9.1266HQ 到 BRANCH1192.168.9.128255.255.255.252192.168.9.129192.168.9.1307HQ 到 BRANCH2192.168.9.132255.255.255.252192.168.9.133192.168.9.1342. 安排IP地址（網關地址使用子網的第一個可用地址）設備接口IP地址子網掩碼默認網關HQFa0/1192.168.9.1255.255.255.224不適用S0/0192.168.9.130255.255.255.252不適用S0/1192.168.9.134255.255.255.252不適用

5、BRANCH1Fa0/0192.168.9.33255.255.255.240不適用Fa0/1192.168.9.49255.255.255.240不適用S0/0192.168.9.129255.255.255.252不適用BRANCH2Fa0/0192.168.9.65255.255.255.240不適用Fa0/1192.168.9.81255.255.255.240不適用S0/1192.168.9.133255.255.255.252不適用PC1網卡192.168.9.2255.255.255.224192.168.9.1PC2網卡192.168.9.50255.255.255.24019

6、2.168.9.49PC3網卡192.168.9.34255.255.255.240192.168.9.33PC4網卡192.168.9.82255.255.255.240192.168.9.81PC5網卡192.168.9.66255.255.255.240192.168.9.653. 連接網絡（路由器之間使用DCE電纜連接到串行口3、 配置每個路由器的接口IP：5 配置每臺計算機的IP地址6. 設置路由器中的路由表。【BRANCH1的配置】下面是配置BRANCH1的IP地址的過程，其它兩個路由器的配置自行完成（1）關閉路由器電源（2）安裝模塊WIT-2T。（3）進入CLI（4）進行以下操作

7、（藍色文字是需要輸入的命令，紅色文字是說明）Continue with configuration dialog? yes/no: nPress RETURN to get started!進入把握臺模式Router>en進入全局配置模式Router#conf tEnter configuration commands, one per line. End with CNTL/Z.修改路由器名稱Router(config)#hostname BRANCH1配置Fa0/0的IP地址BRANCH1(config)#int f0/0BRANCH1(config-if)#ip addr 192.

8、168.9.33 255.255.255.240BRANCH1(config-if)#no shutdown%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up配置Fa0/1的IP地址BRANCH1(config-if)#int f0/1BRANCH1(config-if)#ip addr 192.168.9.49 255.255.255.240BRANC

9、H1(config-if)#no shutdown%LINK-5-CHANGED: Interface FastEthernet0/1, changed state to up%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1, changed state to up配置S0/0的IP地址。由于BRANCH1是BRANCH1和HQ之間串行通信的DCE設備，所以需要配置時鐘頻率。BRANCH1(config-if)#int s0/0BRANCH1(config-if)#ip addr 192.168.9.129 255.

10、255.255.252BRANCH1(config-if)#no shutdown%LINK-5-CHANGED: Interface Serial0/0, changed state to upBRANCH1(config-if)#clock rate 64000%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0, changed state to up返回到把握臺模式。Exit命令返回到上一層，使用Ctrl+Z可以直接返回把握臺。BRANCH1(config-if)#exitBRANCH1(config)#exit%SYS-5

11、-CONFIG_I: Configured from console by console查看IP地址配置狀況。BRANCH1#show ip int briInterface IP-Address OK? Method Status ProtocolFastEthernet0/0 192.168.9.33 YES manual up upFastEthernet0/1 192.168.9.49 YES manual up upSerial0/0 192.168.9.129 YES manual up upSerial0/1 unassigned YES manual administrati

12、vely down down按此方法配置其它兩個路由器，此時可以測試各個子網和網關的連通狀況。（5）添加路由表。這里沒有使用路由總結。BRANCH1#conf tEnter configuration commands, one per line. End with CNTL/Z.BRANCH1(config)#ip route 192.168.9.32 255.255.255.240 f0/0BRANCH1(config)#ip route 192.168.9.48 255.255.255.240 f0/1BRANCH1(config)#ip route 192.168.9.0 255.25

13、5.255.224 192.168.9.130BRANCH1(config)#ip route 192.168.9.64 255.255.255.240 192.168.9.130BRANCH1(config)#ip route 192.168.9.80 255.255.255.240 192.168.9.130返回把握臺BRANCH1(config)#Z%SYS-5-CONFIG_I: Configured from console by console查看路由表BRANCH1#show ip routeCodes: C - connected, S - static, I - IGRP,

14、R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area * - candid

15、ate default, U - per-user static route, o - ODR P - periodic downloaded static routeGateway of last resort is not set 192.168.9.0/24 is variably subnetted, 6 subnets, 3 masksS 192.168.9.0/28 1/0 via 192.168.9.130C 192.168.9.32/28 is directly connected, FastEthernet0/0C 192.168.9.48/28 is directly co

16、nnected, FastEthernet0/1S 192.168.9.64/27 1/0 via 192.168.9.130S 192.168.9.64/28 1/0 via 192.168.9.130C 192.168.9.128/30 is directly connected, Serial0/0【HQ的配置】（1）關閉路由器電源（2）安裝模塊WIT-2T。（3）進入CLI（4）進行以下操作（紅色文字是說明）Continue with configuration dialog? yes/no: nPress RETURN to get started!Router>enRoute

17、r#conf tEnter configuration commands, one per line. End with CNTL/Z.Router(config)#hostname HQHQ(config)#int f0/1HQ(config-if)#ip addr 192.168.9.1 255.255.255.224HQ(config-if)#no shutdown%LINK-5-CHANGED: Interface FastEthernet0/1, changed state to up%LINEPROTO-5-UPDOWN: Line protocol on Interface Fa

18、stEthernet0/1, changed state to upHQ(config-if)#int s0/0HQ(config-if)#ip addr 192.168.9.130 255.255.255.252HQ(config-if)#no shutdown配置IP地址%LINK-5-CHANGED: Interface Serial0/0, changed state to upHQ(config-if)#%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0, changed state to upHQ(config-if)

19、#int s0/1HQ(config-if)#ip addr 192.168.9.134 255.255.255.252HQ(config-if)#no shutdown配置DCE設備的時鐘頻率。HQ是HQ和BRANCH2之間的DCE設備。%LINK-5-CHANGED: Interface Serial0/1, changed state to upHQ(config-if)#clock rate 64000HQ(config-if)#%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/1, changed state to upH

20、Q(config-if)#Z%SYS-5-CONFIG_I: Configured from console by console查看IP地址配置狀況HQ#show ip int briInterface IP-Address OK? Method Status ProtocolFastEthernet0/0 unassigned YES manual administratively down downFastEthernet0/1 192.168.9.1 YES manual up upSerial0/0 192.168.9.130 YES manual up upSerial0/1 19

21、2.168.9.134 YES manual up up添加路由表。這里使用了路由總結（請自行計算是如何總結的！），路由表從5條削減到3條。HQ#conf tEnter configuration commands, one per line. End with CNTL/Z.HQ(config)#ip route 192.168.9.0 255.255.255.224 f0/1HQ(config)#ip route 192.168.9.32 255.255.255.224 192.168.9.129HQ(config)#ip route 192.168.9.64 255.255.255.22

22、4 192.168.9.133HQ(config)#Z%SYS-5-CONFIG_I: Configured from console by consoleHQ#show ip routeCodes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OS

23、PF external type 1, E2 - OSPF external type 2, E - EGP i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area * - candidate default, U - per-user static route, o - ODR P - periodic downloaded static routeGateway of last resort is not set 192.168.9.0/24 is variably subnetted, 5 subn

24、ets, 3 masksC 192.168.9.0/27 is directly connected, FastEthernet0/1S 192.168.9.32/27 1/0 via 192.168.9.129S 192.168.9.64/27 1/0 via 192.168.9.133C 192.168.9.128/30 is directly connected, Serial0/0C 192.168.9.132/30 is directly connected, Serial0/1HQ#【BRANCH2的配置】（1）關閉路由器電源（2）安裝模塊WIT-2T。（3）進入CLI（4）進行以

25、下操作（紅色文字是說明）Continue with configuration dialog? yes/no: nPress RETURN to get started!Router>enRouter#conf tEnter configuration commands, one per line. End with CNTL/Z.Router(config)#hostname BRANCH2配置每個端口的IP地址BRANCH2(config)#int f0/0BRANCH2(config-if)#ip addr 192.168.9.65 255.255.255.240BRANCH2(c

26、onfig-if)#no shutdown%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to upBRANCH2(config-if)#int f0/1BRANCH2(config-if)#ip addr 192.168.9.81 255.255.255.240BRANCH2(config-if)#no shutdown%LINK-5-CHANGED: Int

27、erface FastEthernet0/1, changed state to up%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1, changed state to upBRANCH2(config-if)#int s0/1BRANCH2(config-if)#ip addr 192.168.9.133 255.255.255.252BRANCH2(config-if)#no shutdown%LINK-5-CHANGED: Interface Serial0/1, changed state to upBRA

28、NCH2(config-if)#%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/1, changed state to upBRANCH2(config-if)#Z%SYS-5-CONFIG_I: Configured from console by consoleBRANCH2#show ip int briInterface IP-Address OK? Method Status ProtocolFastEthernet0/0 192.168.9.65 YES manual up upFastEthernet0/1 192.

29、168.9.81 YES manual up upSerial0/0 unassigned YES manual administratively down downSerial0/1 192.168.9.133 YES manual up up添加路由表BRANCH2#conf tEnter configuration commands, one per line. End with CNTL/Z.BRANCH2(config)#ip route 192.168.9.64 255.255.255.240 f0/0BRANCH2(config)#ip route 192.168.9.80 255.255.255.240 f0/1BRANCH2(config)#ip route 192.168.9.0 255.255.255.192 1