1、研華自動化工業數字視訊監控系統簡介與FAQs典型的工業視頻監控系統框圖如下，本系統符合現有大陸國內眾多項目之要求。系統描述：如上圖所示，DVX-4300型IVS系統由研華一臺IPC、PV 系列如PV-600E , PV-800E , PV-1000E, PV-2000E 以及PV-2100E型視頻采集卡和PowerView IVS軟件組成，進行捕捉視訊訊號，顯示現場視頻，并完成智慧視頻偵測，例如可以完成虛擬柵欄（virtual fence）、不明出現目標偵測、丟失物件跟蹤、滯留偵測、跌倒偵測, 人流車流計數偵測功能, 目前提供6個智能視頻偵測功能, 但一臺IPC僅支持其中的4個功能。DVX-4

2、100型DVR是由IPC平臺、PV 系列視頻采集卡和PowerView6000軟件組成，完成視頻記錄功能。DVX-4200型CMS由一臺IPC安裝PowerView CMS組成，完成中央管控功能。DVX-4400型VIS由一臺IPC安裝PowerView VIS軟件組成，完成視頻集成功能，充當視頻Server，從現場的DVR獲取實時視頻畫面并且向internet網絡發布。一般功能之Q&A：DVX-4300型IVS系統部分1， 請問智能視頻監控任務的完成，需要哪幾部分的配合工作？答：IVS采集到視頻畫面，預先設置虛擬柵欄偵測功能，一旦有目標侵入該區域，IVS就會偵測到該入侵行為并且產生一

3、個視頻事件，IVS本身亦能針對事件做處置；當事件發生時，IVS可以反應動作如 DO輸出、快照、聲音播放及執行某一應用程序等四項。這些行為在無需與DVR聯機的情況下即可完成, 或可將該視頻事件描述通過Ethernet網絡傳送給DVR，DVR收到該視頻事件后就會產生相應的預先設定的工作：例如啟動錄像或拍照，云臺啟動跟蹤，發出報警等等。總結：智能視頻監控任務的完成，可以IVS獨立運作或將IVS和DVR兩個系統的緊密配合完成或。2， 請問IVS和DVR的通信，除了上面提到的通過Ethernet網絡，還有別的通信方式嗎？答：目前只有通過Ethernet網絡進行數據交換。3，IVS偵測到入侵行為并且產生一

4、個視頻事件后，能否自己發出DO動作來產生一個報警？答：需要另外增加一塊DO板塊或者ADAM模塊才能完成DO輸出，例如PV-2100E型視頻采集卡本身沒有DO輸出功能。4， IVS的虛擬柵欄功能，在同一幅視頻畫面，可以設置多個區域嗎？答：偵測區域和偵測出的物體是不一樣的；偵測區域最大的上限是11個，但同時偵測物體可達32個。例如防物品丟失功能，最多也可以設置11個跟蹤目標屬于偵測之物體，故理論上可同時偵測32個。相同的,人流/車流計數偵測區域最多也可以設置11個；。5， IVS可以根據智慧視頻分析的結果，進行PTZ控制嗎？答：IVS不能完成PTZ控制。需要DVR的配合來完成該功能。6， IVS和

5、DVR可以共享一個攝像頭嗎？答：IVS和DVR可以共享一個攝像頭，即一個攝像頭分出2條線路分別送給IVS和DVR。但是如果DVR要實現PTZ控制時，最好各自用一路攝像頭，以免沖突。7，IVS偵測到入侵行為并且產生一個視頻事件后，能否進行拍照？答：可以進行拍照，并且存儲在本地硬盤。但是不能遠程發布照片。8， 如果同時需要完成虛擬柵欄偵測和物品丟失偵測，是否可以共享一個攝像頭？答：不能。需要2個攝像頭完成對應功能。9，IVS偵測并且產生一個視頻事件后，能否自己發出信息送給CMS？答：目前IVS不能與CMS直接聯機，IVS需先行與DVR聯機后，再由DVR與CMS連接。故事件的傳送也是IVS->

6、DVR->CMS。DVX-4100型DVR系統部分10, DVR具備那些IVS所沒有的功能？答：視頻錄像和本地視頻備份，云臺控制（PTZ），報警，視頻網絡發布（充當Video Server），字符迭加(iOSD，文本信息顯示于視頻畫面），ADAM 4000/6000集成 , POS , ATM 以及第3方設備集成等.11，DVR的視頻畫面可以通過3G手機或者PMD(手持終端設備)遠程來訪問嗎？答：可以。但是DVR需要鏈入internet網絡，充當視訊服務器，手機或者PMD(手持終端設備)通過Internet網絡訪問DVR的IP地址來獲取視頻畫面。12,我們知道研華可以把IO信息通過iOS

7、D的功能顯示于頻畫面，那么當需要顯示的IO數據變得很多，甚至是成百上千個IO數據需要顯示，怎么辦？答：此時我們可以借助于webaccess來實現。IO數據在webaccess上管理和顯示，視頻畫面嵌入在webaccesss上?？偨Y：當IO資料量很多，視頻畫面不多的情況下，顯示模式采用將視頻畫面嵌入在webaccesss上的方式；反之，需要顯示的IO數據量不多的情況下，采用將IO信息通過iOSD的功能顯示于頻畫面上的模式。13，DVR上面運行的PowerView軟件所顯示的視頻畫面，可以迭加其它圖片或者線條圖框嗎？答：不可以。目前DVR上面運行的PowerView軟件所顯示的視頻畫面，只支持文本

8、標注（即iOSD：Information On Screen Display）。不能迭加其它圖片或者線條圖框。14，可以在一臺IPC上面安裝2塊PV-2100E視頻采集卡，同時運行PowerView6000和PowerView6000 IVS軟件，用一臺IPC實現完整的智能視頻監控功能嗎？答：不能。由于運算負荷的原因，出于可靠性考慮，目前需要兩個工業計算機平臺（IPC或者UNO）來分別運行PowerView6000和PowerView6000 IVS軟件，從而實現完整的智能視頻監控功能。DVX-4200型CMS系統部分15，圖中視頻監控中心的CMS系統，最多可以管理多少攝像頭？DVX-4200

9、最多支持幾重畫面顯示？答：最多可以同時聯機監看最多管理128個攝像頭 , 但可管理DVR的數目不限。DVX-4200,最多支持最多可顯示3個屏幕, 但需要2張顯示卡才能達成3屏幕輸出, 分別有64ch及時監看分割畫面,16ch遠程分割回放,E-MAP,事件過濾顯示, 等幾種顯示方式可讓使用者可選擇。16，圖中視頻監控中心的CMS系統，所顯示的視頻畫面，是由DVR主動發送而來，還是CMS系統主動從DVR獲取數據？答：CMS主動從不同的DVR獲取數據。CMS是客戶端（Client），DVR是視訊服務器（Server）。17，CMS可以實現遠程視頻數據備份（Remote Backup）嗎？答：CMS

10、可以實現遠程視頻實時播放，歷史畫面回放，可予許使用者針對所選擇的DVR攝影機以及選定的時間范圍內做遠程備份。18，VIS和CMS和區別是什么？答：VIS是視頻集成系統，充當視訊服務器，它把各個DVR視頻數據整合在一起，并且通過網絡發布給各個客戶端，例如PMD，與具有MS Mobile OS的3G手機支持與VIS的整合測試 , 可以遠程通過IE來訪問VIS來獲取現場的視頻畫面。CMS是中央監控系統，完成中心視頻管控功能，它是客戶端，網絡的其它客戶端無法訪問CMS主機里面數據。18，CMS可以通過訪問VIS來訪問現場DVR的視頻資料嗎？答：CMS不須通過訪問VIS來訪問現場DVR的視頻數據，CMS

11、可以直接訪問現場的DVR來獲取需要的視頻畫面。19，PowerView6000 ，PowerView6000 IVS，PowerView CMS，PowerView VIS軟件，是否都必需和研華自動化的視頻采集卡硬件配合才能運行？答：PowerView6000 和PowerView6000 IVS不能單獨運行，必須和研華自動化的視頻采集卡硬件配合才能運行，從而完成正常的功能。PowerView CMS，PowerView VIS軟件直接運行于PC機上，不需要視頻采集卡硬件的配合20，PowerView6000 ，PowerView6000 IVS，PowerView CMS，PowerView

12、 VIS軟件，是否都必需和研華自動化的視頻采集卡硬件配合才能運行？答：PowerView6000 和PowerView6000 IVS不能單獨運行，必須和研華自動化的視頻采集卡硬件配合才能運行，從而完成正常的功能。PowerView CMS，PowerView VIS軟件直接運行于PC機上，不需要視頻采集卡硬件的配合21，CMS，VIS，IVS，PTZ名詞縮寫，分別是什么意思？答：CMS: Central Monitoring System中央監控系統VIS：Video Integration System視頻集成系統IVS：Intelligent Video System智能視頻系統DVR:

13、 Digital Video Recorder數字視訊錄像機PTZ: 英文譯義是P-Pan(水平轉動)+T-Tilt(垂直轉動)+Z-Zoom(景深伸縮), PTZ攝像機是由一個可三維轉動的機械云臺和一個可伸縮的鏡頭等構成。PTZ控制就是指的通過軟件實現對云臺機械裝置的控制。22， 哪些軟件收費？哪些軟件免費？答：PowerView 6000：和DVR或者數據采集卡配套所用，免費提供 , 也提供CMSLite可免費使用, 但CMSLite只支持同時聯機32支攝影機, 并只有雙屏幕輸出, 及第一個屏幕是實時遠程監看或切換遠程回放, 第二個屏幕是E-MapPowerView CMS：安裝

14、于獨立的IPC，銷售價格見價格表。CMSLite可免費使用PowerView IVS：和視頻采集卡配套使用，銷售價格見價格表。PowerView VIS：安裝于獨立的IPC，銷售價格見價格表。23， 視訊卡對于硬件平臺系統最低要求各是多少？客戶選型遵循原則是什么？Video CardPV-600, PV-800 , PV-1000 Software CompressionPV-2000, PV-2100 Hardware CompressionCPUIntel P4 2.8 GHz or aboveIntel P4 2.8GHz or aboveMainboardIntel 845, 865

15、or 915 or above chipset Recommanded Mainboard : AIMB-764G2-00A1EAIMB-562AIMB-763Intel 845, 865 or 915 or above chipsetRecommanded Mainboard : AIMB-764G2-00A1EAIMB-562AIMB-763 VGA CardGeforce FX-5200 128MB or Radeon 9200 128MB or aboveATI 9200 128MB or equal (Support DirectX 9)(Support DirectX 9)RAM1

16、024MB or above1024MB or aboveLAN Ethernet 10/100/1000 MHz DirectXDirectX 9（Provided in Powerview CD）HarddiskRecommanded Harddisk capacity : Base on 1.around 7KB per frame ,2. 4 cameras , record 4 frames per second3. 24 hours recording Total HD Capacity : 9.3GB per day。Recommanded min. 80GB harddisk

17、for long time recording and motion detection recording 。OSWindows XP、Windows2000、Window XP Embedded, Windows 2003 serverPower SupplyRecommanded Power consuption :One Harddisk : 250W2-3 Harddisks :300W3-4 Harddisks :350W4-5 Harddisks :400W5-6Harddisks :460W24， 視頻和研華數據采集哪些產品可以整合后一起傳輸？答：可以和ADAM系列模塊和其它I

18、O模塊整合25， 研華視頻支持哪些格式？答：視頻輸入支持模擬量NTSC/PAL制式，視頻輸出支持MPEG1/2/4和H.264壓縮格式。26， 攝像頭種類？答：攝像頭種類為：BNC接頭的NTSC/PAL復合視頻輸出，30/25 fps27， 視頻是否支持IP攝像頭？答：數據采集卡接入的信號均為BNC接頭的NTSC/PAL復合視頻輸入，因此IP攝像頭不能接入到DVR和IVS系統。須等到NVR產品約3Q 2009出來后, CMS或VIS才可與NVR整合。Advantech Automation Industrial Digital Video Surveillance System: Introd

19、uction & FAQsThe following is the layout of the typical industrial video surveillance system, which meets with demands on most projects in China. System Description: As shown above, DVX-4300 IVS system consists of an Advantech IPC platform, a PV series of video capture card, such as PV-600E, PV-

20、800E, PV-1000E, PV-2000E and PV-2100E, as well as PowerView IVS software. It is used to capture video signals, display live video, and complete intelligent video surveillance, such as virtual fence detection, unknown objects detection, object loss detection, object persistence detection, object drop

21、ping detection and passenger/vehicle counting detection. Now six categories of intelligent video surveillance functions are provided, but one IPC can only support four of them. DVX-4100 DVR consists of IPC platform, PV series of video capture card and PowerView6000 software, supporting video record

22、function. DVX-4200 CMS is served by an IPC installed with PowerView CMS software, supporting central control function. DVX-4400 VIS is served by an IPC installed with PowerView VIS software, supporting video capture function. Used as a video server, DVX-4400 VIS captures live video screen from the o

23、n-spot DVR and broadcast it to the internet. Q&A about General Functions:DVX-4300 IVS System3， Q: What cooperated work is needed to complete the intelligent video surveillance task?A: IVS captures the video screen and previously initiate the virtual fence detection function. Once an object invad

24、es, IVS will detect it and trigger a video event. IVS can also deal with this event by itself. When an event happens, IVS can react in the way of DO output, snapshot, audio broadcast and executing some application among others. These actions can be finished without DVR connection. IVS can also send

25、the video event description to DVR through Ethernet, and when receiving it, DVR will execute the previous setup work accordingly, such as starting recording or photographing, pan starting and tracking, and alarming. Conclusion: To complete the intelligent video surveillance task, IVS can run indepen

26、dently, or cooperate closely with DVR system. 4， Q: Apart from Ethernet, is there any other communication way for IVS and DVR?A: At present the data transfer can only be conducted through Ethernet.3， Q: After detecting an invasion action and triggering a video event, can IVS send a DO action and ala

27、rm by itself? A: Another DO block or ADAM module is needed to complete DO output. For example, PV-2100E video capture card itself doesnt have DO output function. 7， Q: As to IVS virtual fence function, can more zones be set within one video screen? A: The detect zones are not the same as the detecte

28、d object. The detect zones are limited within 11, but the detected objects can reach 32 at one time. For example, “For object loss precaution function, 11 tracking targets can also be set at the most”, theoretically 32 objects can be detected at the same time. Likewise, the passenger/vehicle countin

29、g detection zones can also be set to 11 at the most. 8， Q: Can IVS conduct PTZ control according to the intelligent video analysis result? A: IVS cant conduct PTZ control itself. The cooperation with DVR is demanded. 9， Q: Can IVS and DVR share one camera? A: IVS and DVR can share one camera, that i

30、s, one camera can split up 2 lines for IVS and DVR. However, if DVR has to realize the PTZ control function, it is better to use separate cameras to prevent conflict. 7，Q: After detecting an invasion action and triggering a video event, can IVS photograph? A: Yes, but the photos can only be saved at

31、 local disks, and are unable to be sent remotely. 9， Q: If it is need to complete the virtual fence detection and object loss detection at the same time, can one camera be shared? A: No, two cameras are needed to complete the relative functions. 9，Q: After detecting an invasion action and triggering

32、 a video event, can IVS send a message to CMS by itself? A: At present IVS cant directly connect with CMS, but use DVR as a mediator. So the event is transferred like this: IVS->DVR->CMS.DVX-4100 DVR System10, Q: What other functions does DVR have except those of IVS?A: Video record and local

33、video backup, PTZ, alarming, video web broadcast (as Video Server), character addition (iOSD, text displays over video screen), ADAM 4000/6000 integration, POS, ATM, a third device integration11，Q: Can DVRs video screen be remotely visited through 3G cell phone or PMD (Hand-hold Terminal)?A: Yes. Bu

34、t DVR has to connect with internet as a video server, and cell phone or PMD (hand-hold device) visits DVRs IP address through internet and then captures the video screen. 12, Q: We know that Advantech is able to display IO information on video screen through iOSD function, but if more, even thousand

35、s of IO data are in queue, what should we do? A: We can resort to webaccess. IO data can be managed and display on webaccess and video screen is embedded on webaccesss too.Conclusion: When IO information is too much but video images are not, the video screen is embedded on webaccesss; otherwise, whe

36、n the IO information is not too much, IO information displays on video screen through iOSD function. 13，Q: Can the video image displayed by PowerView software running by DVR overlap with other images, lines or frames?A: No. At present, the video image displayed by PowerView software running by DVR o

37、nly supports text labeling (or iOSD: Information On Screen Display), but cant overlap with other images, lines or frames. 14，Q: Can we install 2 PV-2100E video capture cards on one IPC, running PowerView6000 and PowerView6000 IVS software meanwhile, and realize the complete intelligent video surveil

38、lance function by one IPC? A: No. Due to the computing load, in view of the reliability, now two industrial computing platforms (IPC or UNO) are needed to run PowerView6000 and PowerView6000 IVS software meanwhile, and realize the complete intelligent video surveillance function.DVX-4200 CMS System1

39、5，Q: How many cameras can the video surveillance centers CMS system manage at the most? How many tiles of screens can the DVX-4200 display? A: It can manage 128 cameras at the most, but the total number of DVR managed is not limited. DVX-4200 can support 3 screens at the most, which can be achieved

40、through 2 video cards. Users can select 64ch timely monitoring split screen, 16ch remote split playback, E-MAP, event filtering display and other display modes. 16，Q: As to the video images displayed by the video surveillance center's CMS system, are they sent actively by DVR, or actively acquir

41、ed from DVR by CMS system? A: CMS actively acquires data from different DVR. CMS is Client, while DVR is Video Server. 17，Q: Can CMS realize remote backup of video data? A: CMS can realize remote video live broadcast and screen history playback, and allow for remote backup for selected DVR cameras a

42、nd schedules. 18，Q: Whats the difference between VIS and CMS?A: VIS (Video Integration System), used as video server, integrates the video data of all DVR and send them to all clients, such as PMD and 3G cell phone with MS Mobile OS through network. They support VIS integrated tests, and can remotel

43、y visit VIS through IE and capture the live video screen. CMS (Central Monitoring System) is a client and complete central video monitoring. Other clients of the network cant reach CMS internal data. 18，Q: Can CMS reach the live DVR video information through VIS? A: CMS doesn't need to visit the

44、 live DVR video data through VIS. It can directly visit the live DVR and capture the needed video screen. 19，Q: Do PowerView6000, PowerView6000 IVS, PowerView CMS and PowerView VIS software have to work with Advantech Automations video capture card? A: PowerView6000 and PowerView6000 IVS couldnt wor

45、k separately, but have to cooperate with Advantech Automations video capture card to function normally. PowerView CMS and PowerView VIS software can work within PC directly, without the cooperation with the video capture card. 20，What do CMS,VIS, IVS, PTZ stand for and mean?A:CMS: Central Monitoring

46、 System VIS：Video Integration System IVS：Intelligent Video System DVR: Digital Video Recorder PTZ: P-Pan (Horizontal move) + T-Tilt (Vertical Move) + Z-Zoom (Zoom Tele/Wide). PTZ camera is composed of a tri-dimensionally movable mechanical pan and a zoom lens. PTZ Control refers to control on mechan

47、ical pan by software. 21， Q: Which software charge? Which are free? A: PowerView 6000: used with DVR or data acquisition card, free, optional free CMSLite, but CMSLite only supports 32 cameras in connection at one time, and only dual screen output. The first screen is for live remote monitoring

48、 or remote playback shifting, and the other is E-Map.PowerView CMS: installed on separate IPC (see price list for the sales price). CMSLite is free. PowerView IVS: used with video capture card (see price list for the sales price).PowerView VIS: installed on separate IPC (see price list for the sales price).22, Q: Whats video cards lowest standard for hardware platform system? What do users follow when selecting a product? Video CardPV-600, PV-800 , PV-1000 Software CompressionPV-2000, PV-2100 Hardware CompressionCPUIntel P4 2.8 GHz or aboveInt