1、I. SUMMARY OF NOTES技術要求匯總SHEET METAL鈑金： NOTES技術要求（噴涂）：1. INNER BENDING RADII TO BE R_ UNLESS OTHERWISE SPECIFIED未注內折彎圓角R_2. REMOVE ALL SHARP EDGES AND CORNERS 去除毛刺銳邊3. DIMENSIONS ARE TO THEORETICAL SHARP CORNERS尺寸標注為到理論尖角的尺寸4. FINISH: POWDER COATING表面處理： 噴粉NOTES技術要求（鍍鋅）：1. INNER ENDING RADII TO BE R

2、_ UNLESS OTHERWISE SPECIFIED未注內折彎圓角R_2. REMOVE ALL SHARP EDGES AND CORNERS 去除毛刺銳邊3. DIMENSIONS ARE TO THEORETICAL SHARP CORNERS尺寸標注為到理論尖角的尺寸4. FINISH: Fe/Zn_ /D (GB/T 9799, ISO20811)表面處理：Fe/Zn_ /D (GB/T 9799, ISO20811)NOTES: RECOMMEND Fe/Zn5 /D FOR 120H SALT FOG TEST REQUIREMENT AND Fe/Zn12 /D FOR 1

3、92H SALT FOG TEST REQUIREMENT PER ASTM B117.注：對于按照ASTM B117要求，120小時鹽霧試驗要求的推薦電鍍Fe/Zn5 /D，192小時鹽霧試驗要求的推薦電鍍Fe/Zn12 /D. 銅母排COPPER BUSBAR: NOTES 技術要求 (鍍錫)： 1. INNER ENDING RADII TO BE R_ UNLESS OTHERWISE SPECIFIED未注內折彎圓角R_；2. FINISH: BRIGHT TIN PLATING PER ASTM B545按照ASTM B545規定鍍亮錫TIN PURITY: 99.0%, GRAD

4、E: B BRIGHT, CLASS: B, THICKNESS: 5 TIN PURITY: 99.0%, GRADE: B BRIGHT, CLASS: B, THICKNESS: m錫純度：99%， 等級：電鍍亮錫， 類型：B， 厚度 m;3. OTHER NON PLATING SURFACE TO COVER BY HEAT SHRINKABLE TUBING其余非指定電鍍區域用批準的高壓熱縮套;4. COPPER CONDUCTIVITY SHALL BE NO LESS THAN 97%IACS 銅導電率不低于97% IACS.NOTES 技術要求(鍍銀)： 1. INNER E

5、NDING RADII TO BE R_ UNLESS OTHERWISE SPEICIFIED 未注內折彎圓角R_；2. FINISH: SILVER PLANTING PER ASTM B700表面處理：按照ASTM B700鍍銀SILVER PURITY: TYPE3 98.0%, GRADE: B BRIGHT, CLASS: N, THICKNESS: 5m銀純度：3型98%， 等級：亮銀B級， 類型：N， 厚度5 m3. OTHER NON PLATING SURFACE TO COVER BY HEAT SHRINKABLE TUBING 其余非指定電鍍區域用批準的高壓熱縮套。4

6、. COPPER CONDUCTIVITY SHALL BE NO LESS THAN 97%IACS銅導電率不低于97% IACS.5. WELDING 焊裝圖1. WELDING TO BE SOLID AND FREE OF VOIDS, SLAG AND VOID WELDING焊縫牢固可靠，無氣孔、夾渣和虛焊2. GRIND AFTER WELDED 焊后打磨 3. FINISH: PAINT 表面處理：噴漆Or或：FINISH: Fe/Zn_ /D (GB/T 9799, ISO20811)表面處理：Fe/Zn_ /D (GB/T 9799, ISO20811)ASSEMBLY裝配

7、圖：1. ALL FASTENERS USED TO BE GB/ISO GRADE 8.8 UNLESS OTHERWISE NOTED所用的緊固件除非特殊說明，強度均為國標8.8級2. FASTENERS TIGHTENING TORQUE PER SPEC 10110992P1 - Part B螺栓緊固扭矩按照技術條件10110992P1 B部分3. TO LUBRICANT ON THE RELATIVELY MOVING OR ROTATION PLACES WITH GREASE所有運動部件有相對運動處涂潤滑脂INSULATED PARTS絕緣件：1. MATERIAL: 材料：2

8、. RADII TO BE R_ UNLESS OTHERWISE SPECIFIED 未注圓角R 3. COLOR OF PART: 零件顏色：4. UNSPECIFIED DAFT ANGLE: ° 未注拔模斜度：°5. PART TO BE FEE OF SHRINK CAVITY, PORE AND CRACK. PART SURFACE TO BE SMOOTH AND CLEAN WITHOUT MACULA AND MECHANICAL DAMAGE. 零件表面不得有縮松、氣孔和裂紋等缺陷。表面清潔光亮，無損傷。6. THREAD HOLE INSERTS T

9、O WITHSTAND 1.5 TIMES RATED FASTENING TOQUE WITHOUT DAMAGE螺紋嵌件應該能夠承受1.5倍的額定螺栓扭矩?zé)o損壞。7. UNSPECIFIED TOLEARANCE FOLLOW GB1148 OF CLASS MT5未注公差按照GB11486規定MT5級MAHINING PARTS機加工件:1. FILLET TO BE C_ UNLESS OTHERWISE SPECIFIED未注倒角C_2. RADII TO BE R_ UNLESS OTHERWISE SPECIFIED 未注圓角R_3. REMOVE ALL SHARP EDGES

10、 AND CORNERS 去除毛刺銳邊4. FINISH: Fe/Zn_ /D (GB/T 9799, ISO20811)表面處理：Fe/Zn_ /D (GB/T 9799, ISO20811)II. MATERIALS材料規范SpecificationDescription0.75，1.5，2，2.5mm thick mm Al-Zn ALLOY COATED STEEL SHEET DX51D+AZ (GB14978)， mm 敷鋁鋅板 DX51D+AZ (GB14978)4， 5， 6， 8 mm thick mm HOT ROLLED STEEL SHEET (GB/T710), 2m

11、m 熱軋鋼板 (GB710)1.5，2， 2.5， 3mm thick mm COLD ROLLED STEEL SHEET Q235A (GB700), mm 冷軋鋼板 Q235A (GB700)1.5， 2， 2.5，3， 4 mm thick mm STAINLESS STEEL SHEET 12Cr18Ni9 (GB20878), mm 不銹鋼板 12Cr18Ni9 (GB20878)3X40, 4X40,4X60, 5X35, 5X50, 5X60, 5X80, 5X100; 6X30, 6X40, 6X50, 6X80, 6X100, 6X140, 8X40, 8X50, 8X80

12、, 8X60,8X120,8X100,10X40,10X50,10X120,10X80, 10X100, 10X125,12X80, 12X120, 12X150, 15X80, 15X100, 15X120, 15X150TMQY FULL ROUND BUSBAR(GB/5585.1), TMQY 全圓銅母排(GB/5585.1)3X25, 3X30, 4X60,5X30,5X40，6X20， 6X30， 6X40， 6X50， 6X60， 6X100， 6X120， 8X25， 8X40， 8X50， 8X60， 8X100，8X120，10X160，10X30， 10X40，10X50

13、， 10X60， 10X63，10X80， 10X100，10X120， 10X125，10X160， 12X120TMBY ROUND EDGE BUSBAR(GB/5585.1)，TMBY 圓角銅母排(GB/5585.1) HEXAGON STEEL BAR (GB699), 六角鋼(GB699) ROUND STEEL BAR （GB699）, 圓鋼 （GB699） ROUND COPPER BAR T2 GB5231， 圓銅棒T2 GB5231III. STANDARD HARDWARES標準件： SpecificationDescriptionEquivalent Internati

14、onal standardComment1GB5782HEXAGON HEAD BOLTISO40142GB80 HEXAGON SOCKET CONICAL POINT SET SCREWSISO40293GB5783 HEXAGON HEAD BOLTISO40174GB70.1HEXAGON SOCKET CAP SCREWSISO47625GB818 PAN HEAD SCREWS WITH CROSS RECESSEDISO70456GB77HEXAGON SOCKET SET SCREWS WITH FALT POINTISO40267GB6SLOTTED CHEESE HEAD

15、SCREWSISO12078GB953DOUBLE END STUDS9GB6170HEXAGON NUTSISO403210GB93SPRING LOCK WASHERSISO708911GB12618 ? *.1BLIND RIVETISO1597712GB97.1 PLAIN WASHERISO708913GB894.1 SNAP RINGISO40114GB801CARRIAGE BOLTISO867815DK- 4，5，6，8，10，12，14，16SNAP RING16NFE25-511-SKGRIP WASHERNFE25-511-SK17GB6560THREAD FORMING

16、 TAPPING SCREWS18GB70.3HEX SOCKET COUNTERSUNK HEAD SCREWSISO799119GB819.1CROSS RECESSED COUNTERSUNK HEAD SCREWSISO704620GB879.1SPRING ROLL PINISO875221GB91COTTER PINISO1234ITEM 16 GRIP WASHER AS FOLLOWS: ITEM 15 SNAP RING AS FOLLOWS: IV. TERMINOLOGYS術語OUTER LAYER 外層INNER LAYER 內層COUNTERSINK 沉孔SECTION 剖面DIRECTION 方向EMBOSS凸臺SQUARE CUTOUT方孔SLOTTED HOLE 腰圓孔KNOCK-OFF HOLES敲落孔SMOO